Tools & Materials

  • New Light Fixture
  • Work Light
  • Phillips® Tip Screwdriver
  • Needle-Nose Pliers
  • Step Ladder
  • Voltage Tester
  • Continuity Tester
  • Utility Knife
  • Combination Wire Stripper
  • Wire Nuts
  • Extension Cord
  • Electrical Tape
  • Light Bulbs

Intro

Changing a light fixture is an easy way to add some design flair to a room. All it takes is the right tools and some basic knowledge of hooking up electrical wiring. Watch this video and we’ll shed some light on how you can install a new light fixture in your home.

Read Video Transcript

Installing a new light fixture where an old one once was is a great way to add a touch of style and flair to any room in the house. And while it requires some electrical know-how, it’s not that difficult.

Today we’ll shed some light on how to work safely with electricity. We’ll show you some must-have electrical tools for your toolbox and teach you some basic wiring skills that will come in handy for other electrical projects around the house.

But before starting any electrical project, you need to know how to access your electrical service panel to turn off the electrical supply to the circuit you are working on to avoid getting shocked. It’s also extremely important to carefully read and follow the manufacturer’s instructions.

If you have any doubts about performing any of these tasks, you should call a licensed electrician to do the work. But if you’re up for it, let’s get started.

Your project actually begins at the electrical supply panel, which is also commonly referred to as a breaker box. You first need to find the breaker that shuts off the circuit to the room where you are working. This might take a few trips back and forth to the room to double check, and it’s always handy to have some help for this step.

Once you’ve found the correct breaker, flip it to the off position. When you return to the room you’re working in, double check that the power is off by testing the light switch that controls the light you’re replacing. Flip in on and off several times. If the light stays off, you’ve found your circuit.

One handy tool that I am never without on an electrical project is this handy voltage tester. By holding it near the light and pressing the button, a blinking light and beeper signals if there is any live electrical current present. If it signals there is still electrical current, you may have to turn power to the entire house off and proceed with a battery powered light or call an electrician.

Without any light in the room, you’ll need an alternate light source like this halogen work light. Depending on what circuit the light is on, you may need an extension cord to plug the work light into a different room.

Now that we have confirmed that there is no power running to the fixture, it’s time to remove the old light fixture. Most flush mount light fixtures like these come apart in similar fashion.

First, remove the nut that holds the light shade to the fixture pan. This nut might be attached to a finial. Be careful when you unscrew this nut and make sure to support the shade so it doesn’t fall to the floor when the nut comes loose. When loose, pull the shade off the threaded nipple and place it out of the way. Then loosen the screws that hold the fixture pan to the electrical box and remove the fixture pan.

When the fixture pan is free from the junction box, go ahead and disconnect the wires. Remove any electrical tape that covers the wire connectors (or wire nuts as they are commonly called), then unscrew them from the wires. You may have to untwist the wires to separate them from each other using a pair of needle nose pliers. Then disconnect the ground wire. Take the old light down and place it out of the way.

Depending on your new light, if it is a similar style, it will probably install in somewhat the reverse order. But even lights that look similar have slight differences in construction and installation methods. So be sure to read and carefully follow the manufacturer’s instructions to the letter.

To install this light, we’ll first screw our crossbar to the outlet box. Next, we’ll thread the nipple with lock washer and hex nut through the crossbar and position it according to our instructions so it will hold the fixture pan in place flush with the ceiling. For this next part, you may need an extra pair of hands to help you hold the fixture while you re-connect the wires. Once we’ve tweaked the fit and tightened the hex nut to secure it to the crossbar, we’ll hook up our electrical wires, connecting the house black wire to the fixture’s black wire, then the house white wire to the fixture’s white wire and finally, the house ground wire to the fixture’s ground wire.

To make these connections, twist the ends of the wire together in a clockwise direction. After twisting the ends together, cover the twisted wire with a wire nut, twisting clockwise until it is snug. Now we need to wrap each connection with the appropriately colored electrical tape. You’ll do this for each of the three connections, including the black wire, the white wire and the ground wire. When all connections are taped, carefully stuff the connected wires into the outlet box.

With the wiring in place insert the fixture pan through the threaded nipple and finish the installation following the manufacturer’s instructions.

Turn the breaker back on and flip the light switch to the on position and watch your efforts illuminate the room.

Read Video Transcript

Steps

  1. 1.turn off power

    Find the breaker or fuse that shuts off the circuit that you will be working on. Make sure it's in the off position.

  2. 2.flip light switch on and off

    Double check that the power is off by testing the light switch that goes with the light. Flip it on and off several times. If the light stays off, you’ve turned off the right circuit.

  3. 3.use voltage tester

    You can use a voltage tester near the light to check for an electric current.

  4. 4.take of switch plate

    Remove the nut holding the light shade. Be sure to hold it so it doesn't drop. Use an alternative light source if you can't see what you're doing.

  5. 5.unscrew switch from wall

    Loosen the screws holding the fixture pan to the electrical box and remove the fixture pan.

  6. 6.pull switch from wall

    Remove any electrical tape that covers the wire connectors, then unscrew them from the wires. Use needle nose pliers if you need help separating them.

  7. 7.remove the old wires

    If your new light comes with a crossbar, screw it on to the outlet box.

  8. 8.orient new switch

    Reconnect the wires accordingly. Twist the wires together to ensure a connection.

  9. 9.reconnect wires

    Cover the twisted wires with a wire nut, twisting clockwise until snug.

  10. 10.place switch into wall

    Wrap each connection with the appropriately colored electrical tape.

  11. 11.screw switch plate on

    Insert the fixture pan, and finish installing according to the manufacturer's instructions.

  12. 12.test connection

    Turn the power back on and test the connection.

 

How do I troubleshoot a fluorescent fixture that doesn’t light?

It’s probably not the bulb, because they rarely go bad all at once. Wiggle the tube to make sure it is seated. Replace any damaged lamp holders.... More »

My new light fixture is rated for 60W bulbs. Is it OK to use 75W bulbs if I want the room to be brighter?

No. This could cause a serious fire hazard, as the bulbs could get too hot and melt parts of the fixture and even catch on... More »

I’m replacing a light switch. How do I know which wire should be attached to each screw on the new light switch?

If you are replacing an existing switch, make a diagram of how the wires were attached to the old switch before you remove them. Snap a picture with... More »

My fluorescent fixture does not seem to be putting out as much light as it used to. Could the tube be failing?

If the entire tube is dim, it may simply need washing. Try removing it and wiping it with a damp... More »

How do I know the size ballast I need for a fluorescent fixture?

You need to know how many bulbs there are and how long they are. However, make sure you check the starter before you change the ballast. In fact,... More »

What’s causing my fluorescent fixture to hum?

The ballast probably needs replaced. Another sign of a faulty ballast is black tar like substance oozing from the... More »

How do I check the starter in the fluorescent fixture?

Older, delayed-start fluorescent lights flicker when they first light up. If this last more than a couple of seconds, make sure the starter is... More »

How do I connect a wire to the terminal on my light switch?

Bend a stripped wire 180 degrees by bending it over the tip of needle nose pliers. Wrap the wire clockwise around the screw so that it will stay in... More »

What fixture can I use which will enable me to hang a picture straight?

For lightweight pictures, a saw-toothed hanger on picture frames will permit you to adjust the picture on the... More »

Do you have a light switch that I can use to replace one in my house?

Yes, but is it a single pole or is it a three-way switch. A three-way switch is one that is used when a light is controlled by more than one... More »